The actual Cisco 200-125 accreditation will offer the actual accredited card owner a definite edge. The actual 200-125 accredited specialized possesses claimed to your property value this particular accreditation. The actual 200-125 accreditation are worthwhile marketplace regarded experience that your particular proven volume of information along with capacity with the accredited card owner. Just about every dangerous of the 200-125 Cisco adds the modern regular regarding benchmark skills along with capacity with the accredited card owner. This assists the actual prospect to get the beneficial possibilities along with beneficial pay in the Them enterprise.

2016 Sep 200-125 exam engine

Q171. - (Topic 4) 

Which parameter or parameters are used to calculate OSPF cost in Cisco routers? 

A. Bandwidth 

B. Bandwidth and Delay 

C. Bandwidth, Delay, and MTU 

D. Bandwidth, MTU, Reliability, Delay, and Load 

Answer: A 

Q172. - (Topic 8) 

Refer to the exhibit. 

What is the meaning of the term dynamic as displayed in the output of the show frame-relay map command shown? 

A. The Serial0/0 interface is passing traffic. 

B. The DLCI 100 was dynamically allocated by the router. 

C. The Serial0/0 interface acquired the IP address of from a DHCP server. 

D. The DLCI 100 will be dynamically changed as required to adapt to changes in the Frame Relay cloud. 

E. The mapping between DLCI 100 and the end station IP address was learned through Inverse ARP. 

Answer: E 

Q173. - (Topic 2) 

Refer to the exhibit. 

The network administrator normally establishes a Telnet session with the switch from host 

A. However, host A is unavailable. The administrator's attempt to telnet to the switch from host B fails, but pings to the other two hosts are successful. What is the issue? 

A. Host B and the switch need to be in the same subnet. 

B. The switch interface connected to the router is down. 

C. Host B needs to be assigned an IP address in VLAN 1. 

D. The switch needs an appropriate default gateway assigned. 

E. The switch interfaces need the appropriate IP addresses assigned. 

Answer: D 

Q174. - (Topic 9) 

What is the purpose of the POST operation on a router? 

A. determine whether additional hardware has been added 

B. locate an IOS image for booting 

C. enable a TFTP server 

D. set the configuration register 

Answer: A 

Q175. - (Topic 7) 


Refer to the topology. Your company has connected the routers R1. R2. and R3 with serial links. R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2 are also connected to the routers R4 and R5. 

The EIGRP routing protocol is configured. 

You are required to troubleshoot and resolve the EIGRP issues between the various routers. 

Use the appropriate show commands to troubleshoot the issues. 

Why are the pings failing? 

A. The network statement is missing on R5. 

B. The loopback interface is shut down on R5. 

C. The network statement is missing on R1. 

D. The IP address that is configured on the Lo1 interface on R5 is incorrect. 

Answer: C 

200-125 braindumps

Most recent 200-125 pdf exam:

Q176. DRAG DROP - (Topic 6) 


Q177. - (Topic 2) 

What is one benefit of PVST+? 

A. PVST+ supports Layer 3 load balancing without loops. 

B. PVST+ reduces the CPU cycles for all the switches in the network. 

C. PVST+ allows the root switch location to be optimized per VLAN. 

D. PVST+ automatically selects the root bridge location, to provide optimized bandwidth usage. 

Answer: C 

Q178. - (Topic 2) 

Refer to the exhibit. 

At the end of an RSTP election process, which access layer switch port will assume the discarding role? 

A. Switch3, port fa0/1 

B. Switch3, port fa0/12 

C. Switch4, port fa0/11 

D. Switch4, port fa0/2 

E. Switch3, port Gi0/1 

F. Switch3, port Gi0/2 

Answer: C 

Q179. CORRECT TEXT - (Topic 7) 

Answer: Select the console on Corp1 router 

Configuring ACL 


Corp1#configure terminal 

comment: To permit only Host C ({source addr} to access finance server address ( {destination addr} on port number 80 (web) 

Corp1(config)#access-list 100 permit tcp host host eq 80 

comment: To deny any source to access finance server address ( {destination addr} on port number 80 (web) 

Corp1(config)#access-list 100 deny tcp any host eq 80 

comment: To permit ip protocol from any source to access any destination because of the implicit deny any any statement at the end of ACL. 

Corp1(config)#access-list 100 permit ip any any 

Applying the ACL on the Interface 

comment: Check show ip interface brief command to identify the interface type and number by checking the IP address configured. 

Corp1(config)#interface fa 0/1 

If the ip address configured already is incorrect as well as the subnet mask. this should be corrected in order ACL to work 

type this commands at interface mode : 

no ip address 192.x.x.x 255.x.x.x (removes incorrect configured ipaddress and subnet mask) 

Configure Correct IP Address and subnet mask : 

ip address ( range of address specified going to server is given as - ) 

comment: Place the ACL to check for packets going outside the interface towards the finance web server. 

Corp1(config-if)#ip access-group 100 out 


Important: To save your running config to startup before exit. 

Corp1#copy running-config startup-config 

Verifying the Configuration : 

Step1: show ip interface brief command identifies the interface on which to apply access list. 

Step2: Click on each host A,B,C & D . Host opens a web browser page , Select address box of the web browser and type the ip address of finance web server( to test whether it permits /deny access to the finance web Server . 

Step 3: Only Host C ( has access to the server . If the other host can also access then maybe something went wrong in your configuration . check whether you configured correctly and in order. 

Step 4: If only Host C ( can access the Finance Web Server you can click on NEXT button to successfully submit the ACL SIM. 

Q180. - (Topic 4) 

Refer to the exhibit. 

Given the output for this command, if the router ID has not been manually set, what router ID will OSPF use for this router? 





Answer: C