Q21. Which option configures the secondary dial tone option for SRST mode to let the users hear the dial tone for PSTN calls?
A. voice service voipsecondary dialtone 0
B. call-manager-fallbacksecondary dialtone 0
C. dial-peer voice 1 potssecondary dialtone 0
D. ccm-manager secondary dialtone 0
Q22. Refer to the exhibit.
The exhibit shows centralized Cisco Unified Communications Manager configuration components for TEHO calls to U.S. area code 408 from the U.K. The PSTN access code for the U.K. is 9 and 001 for international calls to the U.S. What should the TEHO-US route list configuration consist of?
A. First route group should point only to the U.K. gateway. The second route group should point to the U.S. gateway.
B. First route group should be only the local route group. The second route group should point to the U.S. gateway.
C. First route group should point only to the U.S. gateway. The second route group should be the local route group.
D. The TEHO-US route list should contain only the local route group. The globalized configuration means that the appropriate gateway will be selected automatically.
E. The \+! route pattern should point directly to the U.S. gateway.
Incorrect Answer: A, B, D The route group points to one or more gateways and can choose the gateways for call routing based on preference. The route group can serve as a trunk group by directing all calls to the primary device and then using the secondary devices when the primary is unavailable. One or more route lists can point to the same route group. Link:
Q23. Which commands are needed to configure Cisco Unified Communications Manager Express in SRST mode?
A. telephony-service and srst mode
B. telephony-service and moh
C. call-manager-fallback and srst mode
D. call-manager-fallback and voice-translation
Q24. What happens if location-based CAC is used and there is no bandwidth available when a remote caller is placed on hold?
A. Cisco Unified Communications Manager sends TOH rather than MOH.
B. Cisco Unified Communications Manager terminates the call.
C. Cisco Unified Communications Manager plays default MOH.
D. Cisco Unified Communications Manager attempts to reconnect the call immediately.
Q25. Refer to the exhibit.
The H.323 Gateway is showing status “unknown”. Which statement is true?
A. The gateway must be reset in Cisco Unified Communications Manager.
B. The no gateway command followed by the gateway command must be issued in Cisco IOS.
C. The mgcp commands must be removed.
D. H.323 gateways do not register with Cisco Unified Communications Manager H.323 gateways always show status "Unknown".
E. VUAN 1 20 may be down and so the H.323 gateway appears offline to the Cisco Unified Communications Manager
Incorrect Answer: A, B, C, E
After a gateway is registered with Cisco Unified Communications Manager, gateway registration status may display in Cisco Unified Communications Manager Administration as unknown.
Q26. Which two options must be selected in the SIP Trunk Security Profile configuration between Cisco Unified Communications Manager and Expressway? (Choose two)
A. Enable application-level authorization
B. Accept presence subscription
C. Accept out-of-dialog refer
D. Accept unsolicited notification
E. Accept replaces header
F. Transmit security status
G. Allow charging header
There are two call control systems in this item. The Cisco UCM is controlling the DX650, the Cisco Jabber for Windows Client, and the 7965 and 9971 Video IP Phones. The Cisco VCS and TMS control the Cisco TelePresence Conductor, the Cisco TelePresence MCU, and the Cisco Jabber TelePresence for Windows.
Use the exhibits to answer the following questions.
What two tasks must be completed in order to support calls between the VCS controlled endpoints and the Cisco Unified CM endpoints? (Choose two.)
A. Media Resource Group List.
B. Configure a SIP trunk on the Cisco Unified CM to point to the Cisco VCS.
C. Configure a neighbor zone on the Cisco Unified CM to point to the Cisco VCS.
D. Configure a SIP trunk on the Cisco VCS to point to the Cisco Unified CM.
E. Configure a neighbor zone on the Cisco VCS to point to the Cisco Unified CM.
Q28. Which Cisco IOS command is used to verify that a SAF Forwarder that is registered with Cisco Unified Communications Manager has established neighbor relations with an adjacent SAF Forwarder?
A. show eigrp service-family ipv4 neighbors
B. show eigrp address-family ipv4 neighbors
C. show voice saf dndball
D. show saf neighbors
E. show ip saf neighbors
Incorrect Answer: B, C, D, E
Router# show eigrp service-family ipv4 4453 neighbors
Q29. When an incoming PSTN call arrives at an MGCP gateway, how does the calling number get normalized to a global E.164 number with the + prefix in Cisco Unified Communications Manager?
A. Normalization is done using translation patterns.
B. Normalization is done using route patterns.
C. Normalization is done using the gateway incoming called party prefixes based on number type.
D. Normalization is done using the gateway incoming calling party prefixes based on number type.
E. Normalization is achieved by local route group that is assigned to the MGCP gateway.
Incorrect Answer: A, B, C, E Configuring calling party normalization alleviates issues with toll bypass where the call is routed to multiple locations over the IP WAN. In addition, it allows Cisco Unified Communications Manager to distinguish the origin of the call to globalize or localize the calling party number for the phone user. Link: http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/admin/8_6_1/ccmfeat/fscallpn.html
Q30. DRAG DROP