Our pass rate is high to 98.9% and the similarity percentage between our cisco 300 115 dumps study guide and real exam is 90% based on our seven-year educating experience. Do you want achievements in the Cisco examcollection 300 115 exam in just one try? I am currently studying for the Cisco cisco 300 115 dumps exam. Latest Cisco ccnp switch 300 115 Test exam practice questions and answers, Try Cisco examcollection 300 115 Brain Dumps First.

Q41. A network engineer changed the port speed and duplex setting of an existing EtherChannel bundle that uses the PAgP protocol. Which statement describes what happens to all ports in the bundle?

A. PAgP changes the port speed and duplex for all ports in the bundle.

B. PAgP drops the ports that do not match the configuration.

C. PAgP does not change the port speed and duplex for all ports in the bundle until the switch is rebooted.

D. PAgP changes the port speed but not the duplex for all ports in the bundle.

Answer: A


Q42. Refer to the exhibit.

A network engineer investigates a recent network failure and notices that one of the interfaces on the switch is still down. What is causing the line protocol on this interface to be shown as down?

A. There is a layer 1 physical issue.

B. There is a speed mismatch on the interface.

C. The interface is configured as the target of the SPAN session.

D. The interface is configured as the source of the SPAN session.

E. There is a duplex mismatch on the interface.

Answer: C


Q43. Refer to the exhibit.

The users in an engineering department that connect to the same access switch cannot access the network. The network engineer found that the engineering VLAN is missing from the database. Which action resolves this problem?

A. Disable VTP pruning and disable 802.1q.

B. Update the VTP revision number.

C. Change VTP mode to server and enable 802.1q.

D. Enable VTP pruning and disable 802.1q.

Answer: C


Q44. Which First Hop Redundancy Protocol is an IEEE Standard?

A. GLBP

B. HSRP

C. VRRP

D. OSPF

Answer: C


Q45. Refer to the exhibit.

A multilayer switch has been configured to send and receive encapsulated and tagged frames. VLAN 2013 on the multilayer switch is configured as the native VLAN. Which option is the cause of the spanning-tree error?

A. VLAN spanning-tree in SW-2 is configured.

B. spanning-tree bpdu-filter is enabled.

C. 802.1q trunks are on both sides, both with native VLAN mismatch.

D. VLAN ID 1 should not be used for management traffic because its unsafe.

Answer: C


Q46. When two MST instances (MST 1 and MST 2) are created on a switch, what is the total number of spanning-tree instances running on the switch?

A. 1

B. 2

C. 3

D. 4

Answer: C


Q47. Refer to the exhibit.

A network engineer wants to analyze all incoming and outgoing packets for an interface that is connected to an access switch. Which three items must be configured to mirror traffic to a packet sniffer that is connected to the distribution switch? (Choose three.)

A. A monitor session on the distribution switch with a physical interface as the source and the remote SPAN VLAN as the destination

B. A remote SPAN VLAN on the distribution and access layer switch

C. A monitor session on the access switch with a physical interface source and the remote SPAN VLAN as the destination

D. A monitor session on the distribution switch with a remote SPAN VLAN as the source and physical interface as the destination

E. A monitor session on the access switch with a remote SPAN VLAN source and the physical interface as the destination

F. A monitor session on the distribution switch with a physical interface as the source and a physical interface as the destination

Answer: BCD


Q48. After port security is deployed throughout an enterprise campus, the network team has been overwhelmed with port reset requests. They decide to configure the network to automate the process of re-enabling user ports. Which command accomplishes this task?

A. switch(config)# errdisable recovery interval 180

B. switch(config)# errdisable recovery cause psecure-violation

C. switch(config)# switchport port-security protect

D. switch(config)# switchport port-security aging type inactivity

E. switch(config)# errdisable recovery cause security-violation

Answer: B


Q49. Refer to the exhibit.

Which login credentials are required when connecting to the console port in this output?

A. none required

B. username cisco with password cisco

C. no username with password linepass

D. login authentication default

Answer: A


Q50. Which SDM template is the most appropriate for a Layer 2 switch that provides connectivity to a large number of clients?

A. VLAN

B. default

C. access

D. routing

Answer: A