Proper study guides for Renew Cisco SWITCH Implementing Cisco IP Switched Networks certified begins with Cisco ccnp switch 300 115 preparation products which designed to deliver the Highest Quality cisco 300 115 dumps questions by making you pass the ccnp switch 300 115 pdf test at your first time. Try the free ccnp 300 115 pdf demo right now.

P.S. Highest Quality 300-115 faq are available on Google Drive, GET MORE: https://drive.google.com/open?id=1rTlkzumKqp-6l1APdN9gEEYnSmQquTdN


New Cisco 300-115 Exam Dumps Collection (Question 3 - Question 12)

Q3. Which statement about the configuration of a trunk port as the source of a SPAN session is true?

A. Only VLANs that are configured individually as SPAN sources are monitored.

B. All VLANs on the trunk are monitored.

C. The trunk is errdisabled automatically.

D. All VLANs on the trunk are monitored, provided the SPAN destination port is a trunk.

Answer: B


Q4. Which two statements about StackWise are true? (Choose two.)

A. It groups multiple switch ports as a single EtherChannel.

B. It can use one IP address to communicate with n/w (network).

C. It monitors multiple switches from a central console.

D. It enables multiple switch ports to share a single master configuration.

E. It allows multiple switches to operate as a single switch.

Answer: B,E

Explanation: https://www.cisco.com/c/en/us/products/collateral/switches/catalyst-3750-series-switches/prod_white_paper09186a00801b096a.html


Q5. Refer to the exhibit

A network engineer deployed an older switch with the same spanning-tree priority as the existing root, which caused a network outage. In which two locations should the Spanning Tree protocol root guard feature be implemented? (Choose two.)

A. On the designated root switch downlinks to the access layer.

B. On all of non-root switch facing ports of the access layer

C. On the access layers root facing ports

D. On Layer 3 boundaries in the distribution layer

E. Globally on all network switches.

Answer: A,B


Q6. A switch has been configured with the Vlan dot1q tag native command. Which statement describes what the switch does with untagged frames that it receives on a trunked interface?

A. Untagged frames are forwarded via the default VLAN

B. it drops the untagged frames.

C. The trunked port is put in err-disabled state.

D. Untagged frames are forwarded via the native VLAN

Answer: B


Q7. Which security violation mode drops packets with unknown source addresses and increments the violation counter ?

A. Shutdown

B. Restrict

C. Protect

D. Drop

E. Inhibit

Answer: B


Q8. Which two statements about PortFast are true?

A. The port moves immediately to the forwarding state when a device is connected

B. it allows the port to skip the learning state only.

C. It forces the port to skip all spanning-tree states

D. It is most appropriate for ports that provide connectivity to individual workstations or servers

E. The port is error-disabled if it attempts to move into the listening or /earning states.

Answer: A,D


Q9.

Refer to the exhibit. Which description of the effect of entering the switch port trunk allowed vlan 2,3,4 command on Fast Ethernet 0/2 0 true?

A. The two workstations continue to communication without a default gateway configured.

B. the command is unsupported on a trunk where VLANs have already been pruned manually.

C. The running configuration displays switch port trunk allowed vlan 1-5 for Fa0/2.

D. the two workstation stop communicating because they are on VLAN 5. Which is not allowed on the trunk.

Answer: A


Q10. Refer to the exhibit.

Currently, R1 is the VRRP master virtual router. Which statement about the VRRP configuration on R1 and R2 is true?

A. Communication between VRRP members is encrypted using MD5.

B. R1 has a route to 10.10.1.1/32 in its routing table.

C. R2 does not have a route to 10.10.1.11/32 in its routing table.

D. R2 becomes master if R1 reboots or track in R1 does not fail.

Answer: B


Q11. Behavior of an access port when a tagged packet is received other than the access VLAN value.

A. Tag is removed and packet is forwarded of the VLAN mentioned in the tag.

B. tag is removed and packet is forwarded on the VLAN of the access port

C. Not Available

D. packet is dropped

Answer: D


Q12. CORRECT TEXTThe headquarter office for a cement manufacturer is installing a temporary Catalyst 3550 in an IDF to connect 24 additional users.

To prevent network corruption, it is important to have the correct configuration prior to connecting to the

production network.

It will be necessary to ensure that the switch does not participate in VTP but forwards VTP advertisements that are received on trunk ports.

Because of errors that have been experienced on office computers, all non-trunking interfaces should transition immediately to the forwarding state of Spanning tree. Also configure the user ports (all FastEthernet ports) so that the ports are permanently non-trunking.

Requirement:

You will configure FastEthernet ports 0/12 through 0/24 for users who belong to VLAN 20. Also all VLAN and VTP configurations are to be completed in global configuration mode as VLAN database mode is being

deprecated by Cisco. You are required to accomplish the following tasks:

1. Ensure the switch does not participate in VTP but forwards VTP advertisements received on trunk ports.

2. Ensure all non-trunking interfaces (Fa0/1 to Fa0/24) transition immediately to the forwarding state of

Spanning-Tree.

3. Ensure all FastEthernet interfaces are in a permanent non-trunking mode.

4. Place FastEthernet interfaces 0/12 through 0/24 in VLAN 20.

Answer:

Please Refer to Explanation below for details:

Explanation/Reference:

Console into the Switch Switch>enable Switch#configure terminal

Switch(config)#interface range fa0/1 u2013 24

Switch(config-if-range)#switchport mode access <<Make all FastEthernet interfaces into access mode.

Switch(config-if-range)#spanning-tree portfast <<Enables the PortFast on interface. Next, we need to assign FastEthernet ports 0/12 through 0/24 to VLAN 20. By default, all ports on the switch

are in VLAN 1. To change the VLAN associated with a port, you need to go to each interface (or a range of

interfaces) and tell it which VLAN to be a part of. Switch(config-if-range)#interface range fa0/12 u2013 24

Switch(config-if-range)#switchport access vlan 20 <<Make these ports members of vlan 20 Switch(config-if-range)#exit

Next we need to make this switch in transparent mode. In this mode, switch doesnu2019t participate in the VTP

domain, but it still forwards VTP advertisements through any configured trunk links. Switch(config)#vtp mode transparent

Switch(config)#exit

Switch#copy running-config startup-config


100% Renew Cisco 300-115 Questions & Answers shared by Allfreedumps, Get HERE: https://www.allfreedumps.com/300-115-dumps.html (New 522 Q&As)